If you aren’t getting the actual WiFi speed from your Netgear Orbi, even after setting it up properly, then you must follow the guidelines provided in this post to get the WiFi coverage issue fixed in a flash.
Thus, without much delay, let’s get the ball rolling!
Fix: WiFi Coverage Issue with Netgear Orbi
Fix 1
Placement of Netgear Orbi
To fix the WiFi coverage issue, it is recommended that you take this as one of the most important steps. Scroll down a little!
While placing your Netgear Orbi, it is suggested:
- To place it at the center-most and higher location in your home
- Do not place the Orbi device away from your existing modem
The best place for your Netgear Orbi would be an open, higher, and center-most area in your home.
So, are you getting the best WiFi coverage in every nook and cranny of your house after applying fix 1? Verify it by accessing Orbi Netgear login page on one of your WiFi-enabled devices. But, the WiFi-enabled device must be connected to the Orbi’s SSID.
So, where have you accessed the Orbi Netgear login page? In a basement or in the lobby? In-store room or terrace garden? Don’t forget to share!
Now, here’s to hope that the WiFi coverage issue with your Netgear Orbi is fixed, isn’t it? Still, we request you – do not to close this post. In the future, whenever you face WiFi coverage issues with your Netgear Orbi, you can try the rest of the fixes provided below. Keep reading! Orbi light colors
Fix 2
Update Orbi Firmware
One of the major reasons behind WiFi coverage issues with Netgear Orbi can be outdated firmware versions. So, to get the issue fixed, visit the official site of your Netgear device using orbilogin.net and follow the on-screen firmware update instructions as per the Netgear Orbi model you have.
Fix 3
Power Cycle Your Orbi
Maybe due to overheating of your Orbi, it has started giving your WiFi coverage issues. For fixing this, it is advised to power cycle your Netgear Orbi once a week or whenever you found it overheated.
To power cycle Netgear Orbi, here are the instructions that need to be followed:
Step1: Disconnect every WiFi-enabled device that is connected to the Orbi’s SSID (WiFi network name).
Step2: Turn off your Netgear Orbi.
Step3: Wait for some time.
Step4: Turn the Orbi device back on.
Step5: Connect your WiFi-enabled device to Orbi’s WiFi.
Step6: Access the Orbi Netgear login page to check the WiFi coverage.
Fix 4
Perform Orbi Factory Reset
Performing Orbi factory reset helps in fixing many technical issues with your Orbi device.
So, to reset orbi, here are the instructions that need to be followed:
Step1: Keep your Orbi device plugged in. Ensure to provide your device steady power supply.
Note: Don’t forget to disconnect your devices with Orbi’s WiFi.
Step2: Now, locate the reset hole on your Netgear Orbi.
Step3: Press it using a pin, paper clip, oil pin, or a toothpick.
Step4: Hold the Orbi reset hole for some time and release it.
Note: After resetting Orbi, you have to perform the Orbi setup process again.
In a Nutshell
By following the fixes provided in this article, you will definitely get rid of WiFi coverage issues with your Netgear Orbi.
There is one more thing that we would like to share. Look, Orbi factory reset and power cycle Netgear Orbi are two different processes.
- Orbi factory reset process is used to take back the device to its factory default settings.
- Whereas, power cycling Orbi is used to give the device a fresh start. So, don’t get confused!
Did you find the fixes provided in this article helped you to fix WiFi coverage issues with your Netgear Orbi?