Netgear Router Troubleshooting Lights: An All-Inclusive Guide

Netgear Router Troubleshooting Lights: An All-Inclusive Guide

A Netgear router consists of various LEDs that indicate the status of the connection between your WiFi-enabled devices and router. The LEDs on Netgear router also signifies the status of Ethernet, WPS, WiFi, and Internet connection. But, what if the LEDs on your Netgear router start blinking or become off? Need not to worry! We have come up with this effective Netgear router troubleshooting lights post.

Here, you will get to know everything about how to troubleshoot with Netgear router LEDs. Let’s get started!

Fix: Netgear Router Troubleshooting Lights

Issue 1: Netgear Router Orange/ Amber LED

This is one of the most common yet major issues faced by every second user across the globe. Just in case, your Netgear router is blinking orange or amber, it indicates that there is a poor internet connectivity.

Fix: To fix the issue, do the following:

  • Power cycle your Netgear router. What you have to do is to unplug your Netgear router, wait for a few minutes, and plug it back in again.
  • Check with your ISP. Confirm with your service provider whether you are on an active data plan or not.
  • Faulty wired connection also leads to this issue. In that case, ensure that the Ethernet connection between your Netgear router and modem is successfully established.

Issue 2: Netgear Router Internet LED Blinking White

This type of annoying issue mostly occurs in new Netgear router models. For instance, if you have performed the Netgear router setup, chances are that you might be seeing this error after the process. The blinking white LED indicates that your Netgear router fails to connect to your modem.

Fix: To fix this issue, do the following:

  • First things first, disconnect your Netgear router and modem.
  • Unplug your devices from the wall socket.
  • Wait for a few minutes.
  • Turn on your modem first and then your Netgear router.
  • Reconnect them.
  • Once done, access the routerlogin web-based setup page to see if the issue is fixed now.

Issue 3: Netgear Router RED Power LED

This is one of the most annoying issues that is encountered by every Netgear router user. Don’t sweat over it! We’ve got you covered!

Fix: Thus, to fix this type of annoying issue, do the following:

  • First and foremost, ensure that the Netgear router’s power adapter is properly plugged into a working wall outlet.
  • Push the on/ off button on your Netgear router once to see if its power LED becomes it and green.
  • Place your Netgear router and modem in close proximity.
  • Ensure that your modem and router isn’t hidden inside a cabinet or under a table.

Issue 4: Netgear Router Flashing Blue

This type of issue indicates that your Netgear router is booting up.

Fix: On the off chance if your Netgear router LED is flashing blue, than you need to go through the fixes listed below once.

  • First of all, make sure that your Netgear router’s hardware isn’t damaged.
  • Ensure to update the Netgear router’s firmware. Bear in mind that after performing Netgear router firmware update process, your device will take a couple of minutes to boot up. So, wait patiently for a couple of minutes.
  • Change the default settings of your Netgear router.
  • Make sure to configure your Netgear router properly.
  • Place your Netgear router on a higher and ventilated area.

In a Nutshell

Our post “Netgear router troubleshooting lights” ends here. We hope that after following the fixes listed above, you will be able to fix the annoying LEDs on your Netgear router and to make the most out of it. What’s you feedback? Do share it with us. And if you need more assistance, feel free to drop your wuestions into the comments section.

Gadgets technology